研究了真空脱泡时间、引发剂、单体、交联剂与单体比、固化温度和固相量对低毒的DMAA单体凝胶固化和ZrO2生坯性能的影响.制备了表面光洁、不起皮、不开裂及形状复杂的生坯.在单体浓度为15％,交联剂与单体比为1∶50,引发剂添加量为1％,固化温度为60℃的条件下,采用固相量为52vol％的浆料制备的生坯抗弯强度接近30 MPa,可直接对其进行机械加工.压汞及SEM分析表明:生坯结构均匀,无团聚体及颗粒簇出现,孔径呈较窄的单峰分布,气孔率低(26％),孔径小(最可几孔径为36 nm).
参考文献
| [1] | 黄勇,何锦涛,马天.氧化锆陶瓷的制备及其应用[J].稀有金属快报,2004(06):11-17. |
| [2] | 杨金龙,谢志鹏,汤强,黄勇.α-Al2O3悬浮体的流变性及凝胶注模成型工艺的研究[J].硅酸盐学报,1998(01):41-46. |
| [3] | 许海仙,丘泰.氧化锆陶瓷注凝成型工艺的研究进展[J].电子元件与材料,2010(05):71-74. |
| [4] | Murat B;Elvan Y .Gel-casting of Alumina and Zirconia Using Chitosan Gels[J].Ceramics International,2002,28(04):431-438. |
| [5] | Eva Gregorova;Willi Pabst;Jiri Stetina .Viscoelastic behavior of ceramic suspensions with carrageenan[J].Journal of the European Ceramic Society,2006(7):1185-1194. |
| [6] | Adolfsson E .Gelcasting of zirconia using agarose[J].Journal of the American Ceramic Society,2006(6):1897-1902. |
| [7] | 董满江,毛小建,张兆泉,刘茜.水溶性环氧树脂体系的氧化锆凝胶浇注成型[J].硅酸盐学报,2008(07):1000-1003. |
| [8] | Tao Zhang;Zhaoquan Zhang;Manjiang Dong .The Influence of Polyethylene Imine on the Gelcasting of SiC With Two Different Initiators[J].Journal of the American Ceramic Society,2007(12):3748-3752. |
| [9] | Zhang T;Zhang ZQ;Zhang JX;Jiang DL;Lin QL .Preparation of SiC ceramics by aqueous gelcasting and pressureless sintering[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2007(1/2):257-261. |
| [10] | Jiang D L .Gelcasting of carhide ceramics[J].Nippon Seramikkusu Kyokai Gakujutsu Ronbunshi / Journal of the Ceramic Society of Japan,2008,116(06):694-699. |
| [11] | 陈碧钦,张兆泉,张景贤,林庆玲,江东亮.高固相含量羟基磷灰石浆料的制备及凝胶浇注成型[J].物理化学学报,2008(05):885-889. |
| [12] | 于敬凤 .N,N-二甲基丙烯酰胺线形/变联聚合物的制备及性质研究[D].长春:吉林大学,2004. |
| [13] | 张立明 .陶瓷悬浮液流变特及胶态成型生坯缺陷的控制[D].北京:清华大学,2005. |
| [14] | Marek P .A Catalytic Effect of Alumina Grains onto Polymerization Rate of Methacrylamide-bassed Gelcasting System[J].Ceramics International,2002,32(08):739-744. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%