制备了增强相体积分数为5%～20%的系列Al_(72)Ni_(12)Co_(16P)/A356准晶增强铝基复合材料.其中增强相Al_(72)Ni_(12)Co_(16)通过将严格按化学成分配比的Al_(72)Ni_(12)Co_(16)浇于水冷铜基板上激冷凝固而获得.TEM和XRD分析结果表明所获得的材料为单相准晶材料.准晶增强铝基复合材料经热挤压处理后,绝大部分的铸造缺陷被消除,力学性能测试显示当准晶相的加入量为20%时,铝基复合材料的抗拉强度、屈服强度、弹性模量等性能分别从基体材料的275 MPa、200 MPa和70 GPa提高至410 MPa、350 MPa和102 GPa,而延伸率却从6%降低至3%.分析了准品增强铝基复合材料的断裂机制和增强机制,准品颗粒增强铝基复合材料的断裂机制可能有如下3种:界面及其附近区域脱粘、基体在集中的滑移带内撕裂和颗粒断裂,而其增强机制主要足细晶强化、弥散强化和固溶强化.
Al matrix composites with Al_(72)Ni_(12)Co_(16) particles of volume fraction ranging from 5% ～ 20% were prepared. The quasierystal material was obtained by casting Al_(72) Ni_(12) Co_(16) alloy on the water cooling copper substrate. TEM and X- ray diffraction analysis indicate that the obtained material is single- phase quasicrystal material. Most defects of as-cast composites are eliminated by the hot extrusion, and the mechanical property test reveals that with addition of Al_(72) Ni_(12) Co_(16), the tensile strength, yield strength and elastic modulus of Al matrix composites increase remarkably from 275 MPa, 200 MPa and 70 GPa to 410 MPa, 350 MPa and 102 GPa, respectively; on the other hand, the elongation decreases from 6% to 3%. Based on the above experiment, the fracture mechanism and strengthening mechanism were discussed in detail.
参考文献
| [1] | 佟林松,樊建中,肖伯律.低热膨胀铝基复合材料的研究进展[J].稀有金属,2008,6(3):375-380.Tong Linsong,Fan Jianzhong,Xiao Bolu.Research progress in low thermal expansion aluminum matrix composites[J].Chinese Journal of Rare Metals,2008,6(3):375-380. |
| [2] | 康炘蒙,程小全,张纪奎,郦正能,崔岩.高体积分数SiC_P/Al复合材料的拉伸、压缩与弯曲特性[J].复合材料学报,2008,25(3):127-131.Kang Xinmeng,Cheng Xiaoquan,Zhang Jikui,Li Zhengneng,Cui Yan.Tensile,compressive and flexible properties of high volume fraction SiC_P/Al composites[J].Acta Materiae Compositae Sinica,2008,25(3):127-131. |
| [3] | 孙有平,严红革,陈振华,陈雕.热处理7090/SiC_P铝基复合材料的组织与性能[J].中国有色金属学报,2008,18(5):829-833.Sun Youping,Yan Hongge,Chen Zhenhua,Chen Gang.Microstructures and properties of heat-treated 7090/SiC_P aluminum matrix composite[J].The Chinese Journal of Nonferrous Metals,2008,18(5):829-833. |
| [4] | Srivatsan T S,Al-Hajri M,Smith C,Petraroli M.The tensile response and fracture behavior of 2009 aluminum alloy metal matrix composite[J].Mater Sci Eng A,2003,346(4):91-100. |
| [5] | 车剑飞,黄洁雯,杨娟.复合材料及其工程应用[M].北京:机械工业出版社,2006.Che Jianfei,Huang Jiewen,Yang Juan.Composites and its engineering application[M].Beijing:China Machine Press,2006. |
| [6] | 白朴存,代雄杰,赵春旺,邢永明.Al_2O_3/Al复合材料的界面结构特征[J].复合材料学报,2008,25(1):88-93.Bai Pucun,Dai Xiongjie,Zhao Chunwang,Xing Yongming.Structural features of the interfaces within Al_2O_2/Al composite[J].Acts Materiae Compositae Sinica,2008,25(1):88-93. |
| [7] | 祖丽君.SiC_P/2024复合材料半固态触变成形研究[D].哈尔滨:哈尔滨工业大学,2001.Zu Lijun.Study on semisolid thixoforming of SIC_P/2024 composites[D].Harbin:Harbin Institute of Technology,2001. |
| [8] | Yokoyama Y.Preparation of decagonal Al_2Ni_2Co single quasicrystal by Czochralski method[J].Material Transactions,JIM,1997,38(11):943-959. |
| [9] | Ishihara K N,Yamamoto A.Penrose patterns and related structures Ⅰ:Superstructure and generalized[J].Acta Crystallogr A,1988,44(4),508-516. |
| [10] | Ghomashchi M R,Vikhrov A.Squeeze casting:An overview[J].J Mater Process Technol,2000,101(1-3):1-9. |
| [11] | Thomas M P,King J E.Improvement of mechanical properties of 2124Al/SiC_P MMC plate by optimization of the solution treatment[J].Compos Sci Techn,1996,56 (10):1141-1148. |
| [12] | Ozdemir I,Cocen U,Onel K.The effect of forging on the properties of particulate SiC reinforced aluminium alloycomposites[J].Compos Sci Technol,2000,60(3):411-421. |
| [13] | 郭成,程羽,尚春阳,苏文斌,许建群.SiC颗粒增强铝合金基复合材料断裂与强化机理[J].复合材料学报,2001,18(4):54-57.Guo Cheng,Cheng Yu,Shang Chunyang,Su Wenbin,Xu Jianqun.Mechanisms on fracture and strengthening of aluminium alloy matrix composites reinforced with SiC particles[J].Acta Materiae Compositae Sinica,2001,18 (4):54-57. |
| [14] | 詹美燕,陈振华.SiC_P颗粒增强铝基复合材料塑性变形过程中的强化机制与断裂机制研究[J].材料导报,2004,18(1):57-60.Zhan Meiyan,Chen Zhenhua.Research on strengthening and fracture mechanism of SiC particle reinforced Al matrix composites[J].Materials Review,2004,18(1):57-60. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%