欢迎登录材料期刊网

材料期刊网

高级检索

采用Moldflow对聚丙烯及其短玻璃纤维增强复合材料的注塑成型过程进行3D模拟分析,基于Taguchi试验设计方法(DOE),采用L16(45)正交矩阵进行试验设计,研究工艺参数对注射压力和翘曲变形的影响。结果表明,纤维含量对注射压力和翘曲变形影响作用较为显著,且存在最佳值;模具温度、熔体温度、保压时间和保压压力对注射压力的影响为单调的线性关系,但其对翘曲变形的影响较复杂。

In this paper,the three dimensional numerical simulation was carried out for the mold-filling stage of injection molding of polypropylene(PP) and short-glass fiber reinforced PP by means of moldflow software.Based on Taguchi design of experiments(DOE) method and using an L16(45)orthogonal array,the influence of processing parameters on injection pressure and warpage was investigated.It is shown that the fiber content has a significant effect on the injection pressure and warpage,and has an optimal value.The effects of mould temperature,melt temperature,holding time and holding pressure on injection pressure are monotonous linear,but on warpage defection is complicate.

参考文献

[1] 王利霞,李燕,庄卫国.注塑工艺和玻纤含量对玻纤增强PP注塑制品收缩的影响[J].高分子材料科学与工程,2009(09):135-137,141.
[2] J.L. Thomason .The influence of fibre length and concentration on the properties of glass fibre reinforced polypropylene: 7. Interface strength and fibre strain in injection moulded long fibre PP at high fibre content[J].Composites, Part A. Applied science and manufacturing,2007(1):210-216.
[3] 赵龙志,陈炳辉,杨敏,张尚兵.Moldflow在注射成型翘曲优化中的应用[J].中国塑料,2010(05):78-80.
[4] W.N. OTA;S.C. AMICO;K.G. SATYANARAYANA .Studies on the combined effect of injection temperature and fiber content on the properties of polypropylene-glass fiber composites[J].Composites science and technology,2005(6):873-881.
[5] Ke Wang;Min Guo;Daiguo Zhao .Facilitating transcrystallization of polypropylene/glass fiber composites by imposed shear during injection molding[J].Polymer: The International Journal for the Science and Technology of Polymers,2006(25):8374-8379.
[6] 刘保臣,申长雨,刘春太,上官林建.短纤维增强注塑制品的力学性能分析[J].材料导报,2009(14):80-82,89.
[7] D.CARDOZO .Three Models of the 3D Filling Simulation for Injection Molding: A Brief Review[J].Journal of Reinforced Plastics and Composites,2008(18):1963-1974.
[8] Shen CY;Wang LX;Cao W;Qian L .Investigation of the effect of molding variables on sink marks of plastic injection molded parts using taguchi DOE technique[J].Polymer-Plastics Technology and Engineering,2007(3):219-225.
上一张 下一张
上一张 下一张
计量
  • 下载量()
  • 访问量()
文章评分
  • 您的评分:
  • 1
    0%
  • 2
    0%
  • 3
    0%
  • 4
    0%
  • 5
    0%