研究了纯钼注射成形脱脂和烧结工艺,讨论了热脱脂、溶剂脱脂+热脱脂和烧结工艺对粘结剂脱除率,C、O含量,烧结显微组织和力学性能的影响.结果表明:以正庚烷作为溶剂,在40～50℃下,脱脂2 h后,能脱除60%以上的粘结剂;直接热脱脂样品的C含量高于溶剂+热脱脂,经H2气氛烧结后,两者的C、O含量下降较快,分别小于0.06%和0.0042%;烧结坯的密度随着温度的升高而增加,但当温度高于1850℃时,密度反而下降;材料经1850℃,烧结2 h,其密度和力学性能达到最佳,密度为9.70 g/cm3,抗拉强度为229 MPa,硬度HV10为1930 MPa.
参考文献
| [1] | John A Shield;Gary A Rozak .[J].International Journal of Powder Metallurgy,2005,41(02):21. |
| [2] | Walser D H;Shields D J.[A].Vienna,Austria,2006:14. |
| [3] | Shields D J.Applications of Mo Metal and Its Alloys[M].London:International Molybdenum Association,1995:2. |
| [4] | 牛荣梅,张国君,孙军,魏建峰,孙院军,赵宝华,杨刘晓,马保平.纯钼微观断裂过程的扫描电镜原位观察[J].稀有金属材料与工程,2006(04):559-561. |
| [5] | 钟培全.钼与钼合金的应用及其加工方法[J].中国钼业,2000(05):15-16. |
| [6] | German R M;Bose A.Injection Molding of Metals and Ceramics[M].Princeton:MPIF,1997:1. |
| [7] | Wayne S .[J].Journal of the Less-Common Metals,1973,32(03):321. |
| [8] | Morito F .[J].Journal of Materials Science,1989,24:3403. |
| [9] | Miller MK.;Bryhan AJ. .Effect of Zr, B and C additions on the ductility of molybdenum[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2002(1 SpecialIssueSI):80-83. |
| [10] | 张德尧.氧、氮、碳对钼和钼合金性能的影响[J].中国钼业,2003(02):20-25. |
| [11] | 田建军,陶斯武,张深根,曲选辉.Sm（Co,Cu,Fe,Zr）z永磁体注射成形坯溶剂脱脂工艺的研究[J].粉末冶金工业,2006(02):9-14. |
| [12] | Li Y;Jiang F;Zhao L et al.[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2003,362(1-2):292. |
| [13] | Lee S H;Choi J W;Jeung W Y et al.[J].Powder Metallurgy,1999,42(01):98. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%