从基材注塑成型、真空镀铝和镀铝后产品包装三方面阐述了汽车灯具无底涂真空镀铝的工艺要求。结合镀铝产品常见缺陷成因，介绍了注塑成型和镀铝过程的注意事项。指出无底镀是汽车灯具金属化的发展趋势之一。
The technological requirements of primer-free vacuum aluminum plating on automotive lamp was described from three aspects including injection molding of substrate, vacuum aluminum plating, and packaging of plated products. Some points needing attention during injection molding and vacuum aluminum plating were introduced in combination with the causes of common defects of aluminum plated products. It is pointed out that primer-free plating on substrate is one of the development trends for metallization of automotive lamps.
参考文献
| [1] | 白秀琴,李健,严新平,赵春华.真空镀膜技术在塑料表面金属化上的应用[J].武汉理工大学学报（交通科学与工程版）,2005(06):947-950. |
| [2] | 黄鸿宏,黄洪填,黄剑彬,陈锦珍,王兆勤.真空镀膜综述[J].现代涂料与涂装,2011(06):22-24. |
| [3] | 杨鸣波;唐志玉.高分子材料工程(上)[A].北京:化学工业出版社,2006:218-219. |
| [4] | 崔继耀;谭丽娟.注塑成型技术难题解答[M].北京:国防工业出版社,2007:13-14. |
| [5] | 张甲敏.注塑技术及典型工艺实例[M].北京:化学工业出版社,2010:102-103. |
| [6] | 陶永亮,田雅萍.PC挡风玻璃板注塑工艺设计[J].工程塑料应用,2014(7):46-49. |
| [7] | 陶永亮.模温机在注塑工艺中应用实例[J].现代塑料加工应用,2012(02):52-55. |
| [8] | GB 50073-2013.洁净厂房设计规范[S].北京:中国计划出版社,2013. |
| [9] | 钱知勉.塑料性能应用手册[M].上海:上海科学技术文献出版社,1980:241-242. |
| [10] | 陶永亮.透明件注塑模具保养与实施[J].塑料制造,2012(01):88-91. |
| [11] | FELDER E;BUCAILLE J L;HOCHSTETTER G .Influence de la rhéologie des polymères sur leur résistance a la rayure:étude expérimentale et par simulation numérique[J].Annales de Chimie Science des Matériaux,2003,28(03):15-28. |
| [12] | R.D.K. Misra;R. Hadal;S.J. Duncan .Surface damage behavior during scratch deformation of mineral reinforced polymer composites[J].Acta materialia,2004(14):4363-4376. |
| [13] | 朱俊.轿车车灯的镀铝和免底涂技术[J].汽车与配件,2010(28):23-25. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%