Finite Element Analysis of 100 t Hot Metal Ladle in Process of Tipping

钢铁研究学报(英文版), 2010, 17(11): 19-23.

^1, , ^2, , ^3, , ^4,

1.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

2.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

3.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

4.Department of Mechanical and Electrical Engineering, Baotou Light Industry Vocational and Technical College,Baotou,014035,Inner Mongolia,China

Finite Element Analysis of 100 t Hot Metal Ladle in Process of Tipping

TIAN Hong-yu ^1, , CHEN Fu-rong ^2, , XIE Rui-jun ^3, , LI Shi-hui ^4,

1.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

2.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

3.College of Materials Science and Engineering, Inner Mongolia University of Technology,Hohhot,010051,Inner Mongolia,China

4.Department of Mechanical and Electrical Engineering, Baotou Light Industry Vocational and Technical College,Baotou,014035,Inner Mongolia,China

Keywords： hot metal ladle

Hot metal ladle is an important part in continuous casting production line and its stress distribution has direct influence on its life. In the process of design and calibration of the large-sized hot metal ladle, it is of great significance to determine the stress distribution of each part of the ladle for safely and reliably running the device. Based on 100 t hot metal ladle which is designed by Baotou Iron and Steel Group, simulation of stress field was made by finite element software ANSYS 10. 0 from different dumping angles. Through modeling, loading, restricting and calculating, strain and stress field distribution of the hot metal ladle were acquired. Finally, an assessment of strength and stiffness was made on the hot metal ladle. The results show that in the process of tipping for the hot metal ladle, maximum stress is 132 MPa and maximum strain is only 0. 064% ;maximum stress and strain have appeared in the:stiffener plate which is located at the bottom of the trunnion, and strength and stiffness are qualified. The method, which is convenient and practical, reasonable and reliable, provides theoretical evidence for checking analysis and further optimal design of the hot metal ladle.

参考文献

[1]	李强,高耀东,闻邦椿,韩清凯.40 t钢水包倾翻特性的有限元分析[J].东北大学学报（自然科学版）,2007(07):1021-1024.
[2]	李仕慧,陈芙蓉,刘建祖.铁水罐应力场有限元分析[J].炼钢,2007(03):60-62.
[3]	Chongqing Iron and Steel Design and Research Institute of Ministry of Metallurgical Industry.Mechanical Equipment Design of Ironmaking[M].北京:冶金工业出版社,1985
[4]	LIU Ying.Finite Element Analysis of the Welded Structure of the Ladle's Arm for a 70 t Hot-Metal Ladle Which is Designed by Maanshan Iron and Steel Group[J].Mechanical Engineering,2003(05):29.
[5]	CONG Li-ming;LIU Rong-bing;LIU Jun.Computer Simulation Analysis of a 100 t Hot-Metal Ladle[J].CAD/CAM计算机辅助设计与制造,1999(08):19.
[6]	CONG Li-ming;LIU Rong-bing;LIU Jun .Finite Element Analysis of a 300 t Steel Ladle Exported to Japan[J].Metallurgical Equipment,2000,120(02):12.
[7]	Kimura T O;Akakidani K S;Agiwara M H.Reduction of Molten Steel of Ladle Lining Temperature Drop With Improvement[J].Shinagawa Technical Report,2001(44):1.

上一张下一张

计量

下载量()
访问量()

作者相关

在本站搜索
在百度学术搜索
在万方数据库搜索
在CNKI搜索

文章评分

您的评分：
1

0%
2

0%
3

0%
4

0%
5

0%

材料期刊网

Finite Element Analysis of 100 t Hot Metal Ladle in Process of Tipping

参考文献