采用透射电子显微镜(TEM),对细晶高强IF钢在不同退火温度条件下无沉淀析出区(PFZ)的形成机制及其对材料力学性能的影响规律进行研究.结果表明,由于析出相粒子的固溶和粗大化与晶界迁移造成的扫动效应,导致仅在晶界一侧形成独特的无沉淀析出区,退火过程中无沉淀析出区优先在晶界经过的区域形成.在退火过程中,随着退火温度的升高,细晶高强IF钢无沉淀析出区的平均宽度增大,其屈服强度降低,n值逐渐增加.
参考文献
| [1] | 王利,杨雄飞,陆匠心.汽车轻量化用高强度钢板的发展[J].钢铁,2006(09):1-8. |
| [2] | 李守华,李俊.汽车用高强度IF钢的研究进展[J].上海金属,2007(05):66-70. |
| [3] | 王敏莉,肖利,郑之旺.不同退火温度下Nb＋Ti微合金化高强IF钢板组织和织构的演变[J].金属热处理,2011(07):16-19. |
| [4] | 任硕,陈江华,刘吉梓,方磊,刘萍,明文全,伍翠兰.7150铝合金时效时晶界析出行为的研究[J].电子显微学报,2011(04):444-450. |
| [5] | Tomo Ogura;Shoichi Hirosawa;Tatsuo Sato .Quantitative characterization of precipitate free zones in Al-Zn-Mg(-Ag) alloys by microchemical analysis and nanoindentation measurement[J].Science and technology of advanced materials,2004(4):491-496. |
| [6] | 烟荣一;马场义雄 .PFZ与晶界析出的控制方法[J].日本金属学会会报,1975,19(7):478-482. |
| [7] | Cai B;Adams BL;Nelson TW .Relation between precipitate-free zone width and grain boundary type in 7075-T7 Al alloy[J].Acta materialia,2007(5):1543-1553. |
| [8] | 徐春杰,代盼,屠涛,余玲,张忠明,王锦程.热处理对Mg-5Sn-1Si合金组织及硬度的影响[J].材料热处理学报,2013(10):83-89. |
| [9] | Abe M;Asano K;Fujiwara A .Influence of the precipitate-free zone width on the tensile properties of an Al-6 Zn-l.2 Mg alloy[J].Metallurgical Transactions,1973,4:1499-1505. |
| [10] | Lorimer G W;Nicholson B .Further results on the nucleation of precipitates in theA-l Zn-Mg system[J].Acta Metallurgica,1966,14:1009-1013. |
| [11] | Valeey P C;Day M K B;Sendork A .The structure and mechanical properties of high-purity aluminum-zinc-magnesium alloys[J].Journal of the Institute of Metals,1958,86:337-351. |
| [12] | Thorsten Krol;Dietmar Baither;Eckhard Nembach .The formation of precipitate free zones along grain boundaries in a superalloy and the ensuing effects on its plastic deformation[J].Acta materialia,2004(7):2095-2108. |
| [13] | 王赛玉,石其年.形变热处理对Al-Li合金组织和性能的影响[J].材料热处理学报,2005(05):84-87. |
| [14] | Ryum N .The influence of a precipitate-free zone on the mechanical properties of an Al-Mg-Zn alloy[J].ACTA METALLURGICA,1968,16:327-332. |
| [15] | 王旭,刘仁东,王科强,郭金宇,徐荣杰,孙建伦,孙成钱.鞍钢高强度超细晶IF冷轧汽车板的研制[J].鞍钢技术,2013(04):24-28. |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%