对冷轧带钢轧制过程中因辊缝倾斜调整过量所导致的单边浪缺陷和断带进行了分析,应用影响函数法计算辊系变形,通过迭代计算出附加倾斜后的传动侧轧制力、操作侧轧制力、辊间压力分布、单位宽度轧制力分布、出口厚度横向分布、出口横向张应力分布。理论计算和实际测量结果表明,冷轧机双侧轧制力差值与倾斜调整量呈近似线性增长的规律。根据轧制力差值与倾斜量之间的比例关系,用实测轧制力差值对倾斜值进行动态限幅,可有效避免冷轧过程中断带事故的发生。
The single edge wave and strip break caused by excessive tilting adjustment were analyzed. Influence func tion method was adopted to model the roll deformation. Adding different tilt, roll force of drive side, roll force of operator side, transverse distribution of contact pressure between rolls, transverse distribution of roll force, trans verse distribution of strip thickness at exit side and transverse distribution of tension at exit side were calculated by using iterative method. The theoretical calculation and the actual measurement results show that the difference be- tween the bilateral increases almost linearly with tilt adjustment value. The break strip accidents are effectively aver ted by dynamic limiting to tilt setting value with the measured differential roll force, according to the proportional relationship between the differential roll force and the tilt.
参考文献
| [1] | 王国栋.板形控制和板形理论[M].北京:冶金工业出版社,1986 |
| [2] | 白金兰,王军生,王国栋,刘相华.六辊轧机辊间压力分布解析[J].东北大学学报(自然科学版),2005(02):133-136. |
| [3] | 白金兰,全婉秋,钟凯.冷轧张应力分布模型及其在辊系变形计算中的应用[J].沈阳航空工业学院学报,2008(04):43-47. |
| [4] | 赵启林,刘相华,王国栋.冷轧薄带钢工作辊边部接触研究[J].东北大学学报（自然科学版）,2008(12):1715-1717,1741. |
| [5] | 姜正义,韦东滨,李贺杰,谢海波,朱洪涛,A.K.Tieu,刘相华,张晓明.薄带冷轧接触力学[J].塑性工程学报,2008(03):164-173. |
| [6] | 赵旭亮,王淑君,徐建忠,张殿华.四辊轧机轧辊弹性变形的研究[J].东北大学学报（自然科学版）,2008(06):834-837. |
| [7] | Jiang Z Y;Xiong S W;Tieu A K et al.Modeling of the Effect of Friction on Cold Strip Rolling[J].Journal of Materials Processing Technology,2008,20(01):85. |
| [8] | 龚寄,王艾伦,骆拓.四辊轧机有载辊缝解析模型研究[J].中国机械工程,2007(22):2752-2756. |
| [9] | 白金兰,张睿,刘红,李东辉,王国栋.冷轧带钢轧制压力分布计算[J].沈阳航空工业学院学报,2004(04):26-28. |
| [10] | 连家创 .变分法求解辊缝中金属横向流动问题[J].东北重型机械学院学报,1980,1(01):1. |
| [11] | 吕程,矫志杰,刘相华.考虑轧件弹性变形的Hill轧制力显式公式[J].钢铁研究,2000(03):32. |
| [12] | 李俊洪 .板带轧机板形计算理论及其在宽带轧制中应用研究[D].燕山大学,2003. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%