在室温下以等径弯曲通道变形(ECAP)技术制备超细晶工业纯钛,利用光学显微镜(OM)和透射电子显微镜(TEM)研究室温ECAP变形纯钛微观组织演变过程,并讨论纯钛室温ECAP变形的显微组织演化机制.结果表明:显微组织演化分为3个不同阶段,分别对应3种不同机制:第一阶段在真应变ε≤1.27时,为位错滑移和孪生交互作用细化机制,形成含有高密度位错和孪晶的板条状组织;第二阶段在真应变量1.27＜ε＜2.54时,为动态回复细化机制,晶粒进一步细化至～0.25μm,形成典型的变形亚晶组织;第三阶段在真应变量ε≥2.54时,为不平衡晶界的转动细化机制,形成平均晶粒尺寸约为0.2μm的等轴状大角度晶界超细晶组织.
参考文献
| [1] | Stolyarov VV;Lowe TC;Islamgaliev RK;Valiev RZ;Zhu YT .Two step SPD processing of ultrafine-grained titanium[J].Nanostructured Materials,1999(7):947-954. |
| [2] | KIM I;JEONG W S;KIM J et al.Deformation structures of pure Ti produced by equal channel angular pressing[J].Seripta Materialia,2001,45(05):575. |
| [3] | Vladimir V. Stolyarov;Y. Theodore Zhu;Igor V. Alexandrov;Terry C. Lowe;Ruslan Z. Valiev .Influence of ECAP routes on the microstructure and properties of pure Ti[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2001(1/2):59-67. |
| [4] | STOLYAROV V V;ZHU Y T;LOWE T C et al.Microstructure and properties of pure Ti processed by ECAP and cold extrusion[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2001,303(1-2):82. |
| [5] | Shin DH.;Kim I.;Kim J.;Zhu YTT. .Shear strain accommodation during severe plastic deformation of titanium using equal channel angular pressing[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2002(1/2):239-245. |
| [6] | D.H. Shin;I. Kim;J. Kim .Microstructure development during equal-channel angular pressing of titanium[J].Acta materialia,2003(4):983-996. |
| [7] | ZHU Y T;KOBOLOV YU R;GRABOVETSKAYA G P et al.Microstructures and Properties of Ultrafine-grained Ti Foil processed by ECAP and Cold Rolling[J].Journal of Materials Research,2003,18:1011. |
| [8] | ZHU Y T;HUANG J Y;GUBICZA J et al.Nanostructures in Ti processed by severe plastic deformation[J].Journal of Materials Research,2003,18:1908. |
| [9] | KIM I;KIM J;KIM D H et al.Effects of grain size and pressing speed on the deformation mode of commercially pure Ti during equal channel angular pressing[J].Metall Mater Trans(A),2003,A34:1555. |
| [10] | I. Kim;J. Kim;D. H. Shin;X. Z. Liao;Y. T. Zhu .Deformation twins in pure titanium processed by equal channel angular pressing[J].Scripta materialia,2003(6):813-817. |
| [11] | Stolyarov VV.;Zhu YT.;Alexandrov IV.;Lowe TC.;Valiev RZ. .Grain refinement and properties of pure Ti processed by warm ECAP and cold rolling[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2003(1/2):43-50. |
| [12] | Kim I.;Kim J.;Shin DH.;Lee CS.;Hwang SK. .Effects of equal channel angular pressing temperature on deformation structures of pure Ti[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2003(1/2):302-310. |
| [13] | STOLYAROV V V;SHUSTER L SH;MIGRANOV M SH et al.Reduction of friction coefficient of ultrafinegrained CP titanium[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2004,371(1-2):313. |
| [14] | Woo-Jin Kim;Chang-Young Hyun;Ho-Kyung Kim .Fatigue strength of ultrafine-grained pure Ti after severe plastic deformation[J].Scripta materialia,2006(10):1745-1750. |
| [15] | Young Gun Ko;Dong Hyuk Shin;Kyung-Tae Park .An analysis of the strain hardening behavior of ultra-fine grain pure titanium[J].Scripta materialia,2006(10):1785-1789. |
| [16] | Akihiro Yamashita;Daisuke Yamaguchi;Zenji Horita;Terence G. Langdon .Influence of pressing temperature on microstructural development in equal-channel angular pressing[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2000(1):100-106. |
| [17] | SEMIATIN S L;SEGAL V M;GOFORTH R E et al.Workability of commercial-purity titanium and 4340 steel during equal channel angular extrusion at cold-working temperatures[J].Metallurgical and Materials Transactions,1999,A30:1425. |
| [18] | Xicheng Zhao;Wenjie Fu;Xirong Yang .Microstructure and properties of pure titanium processed by equal-channel angular pressing at room temperature[J].Scripta materialia,2008(5):542-545. |
| [19] | 付文杰,赵西成,杨西荣,郑艳霞.室温等径弯曲通道变形工业纯钛的组织及性能研究[J].热加工工艺,2007(18):21-23,61. |
| [20] | 付文杰,赵西成,杨西荣,兰新哲.室温ECAP和冷轧复合变形工业纯钛的组织和性能[J].材料研究学报,2008(03):303-306. |
| [21] | 杨西荣,赵西成,付文杰.工业纯钛在120°模具中的多道次ECAP室温变形组织与性能[J].稀有金属材料与工程,2009(06):955-957. |
| [22] | OH-ISHI K;HORITA Z;FURUKAWA M et al.Optimizing the rotation conditions for grain refinement in equal-channel angular pressing[J].Metallurgical and Materials Transactions A,1998,29:2011. |
| [23] | C. Pithan;T. Hashimoto;M. Kawazoe;J. Nagahora;K. Higashi .Microstructure and texture evolution in ECAE processed A5056[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,2000(1):62-68. |
| [24] | A. GHOLINIA;P. B. PRANGNELL;M. V. MARKUSHEV .THE EFFECT OF STRAIN PATH ON THE DEVELOPMENT OF DEFORMATION STRUCTURES IN SEVERELY DEFORMED ALUMINIUM ALLOYS PROCESSED BY ECAE[J].Acta materialia,2000(5):1115-1130. |
| [25] | S. D. Wu;Z. G. Wang;C. B. Jiang;G. Y. Li;I. V. Alexandrov;R. Z. Valiev .The formation of PSB-like shear bands in cyclically deformed ultrafine grained copper processed by ECAP[J].Scripta materialia,2003(12):1605-1609. |
| [26] | Y. Fukuda;K. Oh-ishi;Z. Horita .Processing of a low-carbon steel by equal-channel angular pressing[J].Acta materialia,2002(6):1359-1368. |
| [27] | FIGUEIREDO R B;LANGDON T G.The nature of grain refinement in equal-channel angular pressing:a comparison of representative fcc and hcp metals[J].International Journal of Materials Reaearch,2009(12):1638-1648. |
| [28] | KAWASAKI M;HORITA Z;LANGDON T G .Microstructural evolution in high purity aluminum processed by ECAP[J].Materials Science and Engineering A:Structural Materials Properties Microstructure and Processing,2009,524:143. |
| [29] | P.3.瓦利耶夫;и.B.亚力克山卓夫;林柏年.剧烈塑性形变纳米材料[M].北京:科学出版社,2006 |
| [30] | 余永宁.金属学原理[M].北京:冶金工业出版社,2007 |
上一张
下一张
上一张
下一张
计量
- 下载量()
- 访问量()
文章评分
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%