金属圆锯片广泛用于金属材料、石材的切割，在工业生产中有十分重要的作用。圆锯片淬火是锯片生产的第1步，对锯片质量影响很大。在对φ1200级65Mn 圆锯片淬火热处理后发现，一次淬火后的圆锯片经压平处理后仍存有一定的瓢曲变形，重新淬火后再次压平瓢曲变形消失。为此根据淬火后65Mn 锯片的金相组织和硬度，利用 MARC 有限元软件对淬火的升温过程进行了研究。结果显示，一次淬火时的升温过程中的最高温度为715．9℃，最低温度为702．2℃，材料并未完全奥氏体化。重新淬火时，由于淬火后的马氏体的奥氏体化速率高于珠光体，使锯片的奥氏体化程度进一步提升，性能得到改善，瓢曲变形消失。
Metal circular saw blade is widely used in the cutting of metal materials and stones,which has a vital posi-tion in industries.Quenching is the first step of the production of circular saw blade and has a significant effect on the quality of saw blade.It has been found that theφ1 200 class 65Mn circular saw blade has a remarkable flexure deformation after quenching and flattening treatment,but this deformation disappears after second quenching and flattening treatment.Based on the microstructure and hardness of the quenched 65Mn saw blade and by use of the MARC simulation software,the heating process of first quenching treatment was studied.It was found that after the first heating process in which the temperature ranges between 715.9℃ and 702.2℃ the saw blade was not fully austenitized.In the second heating process,since the austenitizing rate of martensite exceed the lamellar pearlite, the austenitizing degree and the relevant properties of the saw blade were improved,and thus the flexure deforma-tion disappeared.
参考文献
| [1] | 寇元哲.模具钢淬透性及淬火变形分析研究[J].模具技术,2010(01):55-58. |
| [2] | Doane D V .Application of hardenability concepts in heat treatment of steel[J].Heat Treating,1979(1):5.,1979. |
| [3] | 《钢的热处理裂纹和变形》编写组.钢的热处理变形和裂纹[M].北京:机械工业出版社,1978:95.,1978. |
| [4] | 周禹城,梁国平 .钢材轧制中的拉拔效应及热塑有限元计算[J].中国冶金,2008,18(7):25.,2008. |
| [5] | 刘庄.热处理过程的数值模拟 [M].北京:科学出版社, 1996:283.,1996. |
| [6] | 周禹城,梁国平 .热塑有限元的理论及应用[J].中国冶金,2014,24(6):36.,2014. |
| [7] | 郭继富.金属冷切圆锯片在轧钢生产中的应用[J].冶金设备,2005(01):43-48. |
| [8] | 祝志峰,赵征志,赵爱民.600MPa级热轧双相钢的组织性能[J].钢铁,2011(09):82-85. |
| [9] | ZHAO Ming-chun,YANG Ke,XIAO Fu-ren,et al.Continu-ous cooling transformation of undeformed and deformed low carbon pipeline steel[J].Master Sci Eng:A,2003(355):126.,2003. |
| [10] | 邝霜,齐秀美,尉冬,刘光明.不同马氏体体积分数双相钢的显微组织变化特征[J].钢铁,2012(10):83-86,96. |
| [11] | PAN Jian-sheng .Research and application prospect of com-puter simulation on heat treatment process[J].Journal of Shanghai Jiaotong University:E,2000,5(1):1.,2000. |
| [12] | DONG Y J.On the material process simulation code COS-MAP-simulated examples and its experimental verification for heat treatment verification for heat treatment process[J].Key Engineering Materials,2007(5):345.,2007. |
| [13] | 沈晓辉,闫军,安涛,肖锋,许章泽.车轮热处理过程中的变形分析[J].中国冶金,2007(07):19-22. |
| [14] | 雷雪 .低压转子加热过程模拟及工艺优化[D].上海交通大学,2009. |
| [15] | 崔忠圻,覃耀春.金属学与热处理[M].北京:机械工业出版社,2007:238.,2007. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%