针对600 MPa级别TRIP钢，进行了760、780、800、820、840、860℃两相区退火温度试验，利用扫描电镜和拉伸试验机等设备，分析了其对应的组织比例和力学性能检验结果，得出结论：随着两相区退火温度的升高，铁素体体积分数逐渐减少，钢板的抗拉强度值不断增加，但伸长率值却先下降再升高，在820℃伸长率有最大值，这与820℃时较高残余奥氏体体积分数和最大残奥中碳质量分数相对应，说明TRIP效应可以改善钢板的塑性指标，获得最佳强塑组合；在800～820℃的两相区转变温度范围内，强塑积可以达到2.17×104 MPa·%，为600 MPa级TRIP钢退火工艺提供了实际指导。
Aiming at 600 MPa TRIP steel,the experiments of intercritical annealing at 760,780,800,820,840, 860℃,respectively,were carried out. By means of scanning electron microscopy and tensile test,the phase proportion and the mechanical property were measured and analyzed. It was found that with the increase of intercritical annealing temperature,the ferrite content gradually reduced,the tensile strength gradually increased,while the tensile elongation first decreased and then increased with a maximum value at 820℃. This maximum elongation was attributed to the best combination of austenitic volume fraction and carbon content,indicating that the TRIP effect can improve the plasticity and thus results in a best combination of strength and plasticity. In the annealing temperature range at 800-820 ℃,a maximum value of the product of strength to ductility about 2.17 × 104 MPa ·%was obtained,which was useful to the design of annealing process of the 600 MPa TRIP steel.
参考文献
| [1] | 王国栋.钢铁行业技术创新和发展方向[J].钢铁,2015(9):1-10. |
| [2] | Takehide SENUMA.Physical Metallurgy of Modern High Strength Steel Sheets[J].ISIJ International,20016(6):520-532. |
| [3] | 胡智评;许云波;谭小东.一种 Mn -Al 系 TRlP 钢的临界区奥氏体稳定化研究[J].东北大学学报（自然科学版）,2016(2):179-183. |
| [4] | 江海涛;唐荻;刘强;刘仁东;严玲.TRIP钢中残余奥氏体及其稳定性的研究[J].钢铁,2007(8):60-63,82. |
| [5] | 任勇强;陈二虎;宋婷婷;袁胜福;尚成嘉.高延伸膨胀管用钢的力学性能及微观组织[J].钢铁,2014(4):63-68. |
| [6] | 韩志勇;张明达;徐海峰;董瀚;曹文全.高性能汽车钢组织性能特点及未来研发方向[J].钢铁,2016(2):1-9. |
| [7] | 定巍;龚志华;唐荻;江海涛;王宝峰.一种含回火马氏体组织TRIP钢的研究[J].材料热处理学报,2013(2):42-46. |
| [8] | 刘强;江海涛;唐荻;刘仁东;唐小勇.TRIP钢中残余奥氏体相变与断裂机制研究[J].塑性工程学报,2009(1):156-161. |
| [9] | 刘艳林.一种Fe-C-Si-Mn-Cr-Mo钢碳配分行为对组织的影响[J].钢铁,2016(4):53-58. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%