在用整辊内嵌式板形检测辊检测可逆冷轧生产过程中带钢的在线板形状况时，板形检测辊的热变形影响辊体内孔面与传感器顶部间过盈配合面的接触状况，引起板形检测信号的间断消失。以整辊内嵌式板形检测辊为研究对象，应用有限元技术对冷轧可逆轧制各道次中检测辊辊体内孔面与骨架顶部过盈配合面各节点副的温度差值、径向相对位移进行模拟分析，获取温度差值对各节点副相对位移和传感器预压力的影响规律。分析结果表明，第3道次各节点副的温度差值最大，大部分节点副的径向相对位移超过配合过盈量，使得传感器预压力接近零，严重影响带钢作用在辊体表面的压力传递，容易造成板形检测信号的中断。
In the process of cold reversible strip flatness detected by entire roller embedded shapemeter roll,the contact condition of interference fit surface between the top surface of framework and the inner hole surface of roll body is af-fected by thermal deformation,so the cold strip flatness detection signal may be interrupted or even disappeared. For en-tire roller embedded shapemeter roll,the temperature differences and radial relative displacements of contact node pairs on the interference fit surface between the top surface of framework and the inner hole surface of roll body,were ana-lyzed using the finite element technology in cold reversible rolling passes. The influences of temperature differences on radius relative displacements of the contact node pairs and the sensor pre-pressure were obtained. The results show that the maximum temperature difference of the contact node pair occurs in the third rolling pass,and most of radial relative displacements of contact node pairs exceed the value of interference fit,which makes the sensor pre-pressure be close to zero. So the transfer of pressure that the strip applied on the outer surface of shapemeter roll is seriously affected,and the shape measuring signal is interrupted.
参考文献
| [1] | 彭开香;童朝南;董洁;李谋渭.1400mm铝带箔冷轧机板形控制系统[J].冶金自动化,2004(4):32-35. |
| [2] | 杨利坡;于丙强;李荣民;刘宏民;杜长征.冷轧带钢板形检测误差及异常信号补偿模型[J].机械工程学报,2014(6):30-38. |
| [3] | 杨利坡;于丙强;孙亚波;王军生.冷轧带钢在线板形信号补偿技术及工业应用[J].机械工程学报,2011(12):56-61. |
| [4] | YANG Li-po;YU Bing-qiang;DING Dong;LIU Hong-min.Industrial shape detecting system of cold rolling strip[J].中南大学学报（英文版）,2012(04):994-1001. |
| [5] | LIU Jia-wei;ZHANG Dian-hua;WANG Jun-sheng;WANG Peng-fei.Deflection Compensation Model for Flatness Measuring Roll[J].钢铁研究学报（英文版）,2010(12):35-37,45. |
| [6] | 张清东;文杰.冷轧带钢板形分段接触式检测过程的力学建模与仿真[J].工程力学,2013(7):235-241,254. |
| [7] | 吴海淼;刘宏民;于丙强;杨利坡.Determination of interference fit value on entire roller embedded shapemeter roll[J].中南大学学报（英文版）,2014(12):4503-4508. |
| [8] | 吴海淼;刘宏民;于丙强;杨利坡.整辊内嵌式板形检测辊瞬态温度场与应力场分析[J].钢铁,2014(5):47-51. |
| [9] | LI Chang-sheng;YU Hai-liang;DENG Guan-yu.Numerical Simulation of Temperature Field and Thermal Stress Field of Work Roll During Hot Strip Rolling[J].Journal of iron and steel research,20075(5):18-21. |
| [10] | 韩继铖;任学平.热轧带钢轧机工作辊热应力的有限元分析[J].包头钢铁学院学报,2006(4):352-356. |
| [11] | Fabien Volle;Michel Gradeck;Denis Maillet;Arsene Kouachi;Michel Lebouche.Inverse Heat Conduction Applied to the Measurement of Heat Fluxes on a Rotating Cylinder: Comparison Between an Analytical and a Numerical Technique[J].Journal of heat transfer: Transactions of the ASME,20088(8):081302-1-8-0. |
| [12] | 周燕;肖刚;胡秋.轧辊温度场热交换系数的一种简便确定方法[J].钢铁研究,2002(2):37-38. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%