采用热压烧结方法分别制备了 Al2 O 3-TiCN 复合陶瓷(AT)及掺杂 MgO-Y2 O 3复合助剂的 Al2 O 3-TiCN 复合陶瓷(ATMY)；研究了烧结温度和 MgO-Y2 O 3复合助剂对复合陶瓷相对密度、显微组织及力学性能的影响.结果表明：当烧结温度在1400~1600℃时,AT 和 ATMY 的相对密度均在97．3％以上；当烧结温度不超过1500℃时,利用第二相 TiCN 可有效抑制 Al2 O 3晶粒长大,AT 和 ATMY 的显微组织、断裂韧度均无明显差异；当烧结温度超过1500℃时,TiCN 不能有效地抑制 Al2 O 3晶粒长大,导致 AT 显微组织粗化,在1600℃烧结的 AT 的断裂韧度为4．5 MPa.m 1
Al2 O 3-TiCN ceramic (AT)and MgO-Y2 O 3 doped composite ceramic (ATMY)were fabricated by hot-pressing sintering.The effects of sintering temperature and MgO-Y2 O 3 additive on the relative density, microstructure and mechanical property of composite ceramics were studied.The results show that the relative density of AT and ATMY was not less than 97.3% at the sintering temperature from 1 400 ℃ to 1 600 ℃.When the sintering temperature was no more than 1 500 ℃,the second phase of TiCN could effectively inhibit grain growth in Al2 O 3 substrate due to the grain boundary pinning effect,and there was no obvious difference between AT and ATMY of the microstructures and fracture toughness.When the sintering temperature was higher than 1 500 ℃,TiCN phase was unable to inhibit the grain growth of Al2 O 3 ,resulting in the microstructure coarsening of AT.The fracture toughness of AT sintered at 1 600 ℃ was 4.5 MPa. m1/2 .The doped MgO-Y2 O 3 additive cooperated with the second phase of TiCN could effectively inhibit the grain growth in Al2 O 3 substrate.When sintered at 1 600 ℃,the microstructure of ATMY was small and uniform,and the fracture toughness reached as high as 5.1 MPa.m1/2 .
参考文献
| [1] | 吕仁江,张福祥,李英杰,侯学功.阳极氧化铝模板合成介孔ZrO2纳米线及其光致发光性能[J].机械工程材料,2013(10):83-86,95. |
| [2] | KATARINA B;PAVOL S;DUGAN G et al.Two-stage sintering of alumina with submicrometer grain size[J].Journal of the American Ceramic Society,2007,90(1):330-332. |
| [3] | FARHAD G F;MEHD;MASOUD A et al.Microstructural evolution of a commercial ultrafine alumina powder densified by different methods[J].Journal of the European Ceramic Society,2011,31:2593-2599. |
| [4] | TENG Y C;SUN Z P;TANG J Y et al.High-pressure sintering of microcrystalline and highly purified aluminal ceramic[J].Journal of the Chinese Ceramic Society,2007,35(8):968-972. |
| [5] | ZHAO J H;HARMER M P .Sintering of ultra-high-purity alumina doped simultaneously with MgO and FeO[J].Journal of the American Ceramic Society,1987,70(12):860-866. |
| [6] | FANG J X;THOMPSON M;HARMER M P et al.Effect of yttrium and lanthanum on the final-stage sintering behavior of ultrahigh-purity alumina[J].Journal of the American Ceramic Society,1997,80(8):2005-2012. |
| [7] | RAK Z S;CZECHOWSKI J .Manufacture and properties of Al2 O 3-TiN particulate composites[J].Journal of the European Ceramic Society,1998,18(4):373-380. |
| [8] | XU C H .Preparation and performance of an advanced multiphase composite ceramic material[J].Journal of the European Ceramic Society,2005,25(5):605-611. |
| [9] | SWARNAKA A K;HUANG S G;VAN D B et al.Ultrafine Al2 O 3-B4 C composites consolidated by pulsed electric current sintering[J].Journal of Alloys and Compounds,2010,499(2):200-205. |
| [10] | LIU J;OWNBY P D .Enhanced mechanical properties of alumina by dispersed titanium diboride particulate inclusions[J].Journal of the American Ceramic Society,199 1,74(1):241-243. |
| [11] | GONG J G;MIAO H Z;ZHAO Z et al.Fracture toughness of Al2 O 3-TiCN composites[J].Journal of Materials Science Letters,2001,20:2085-2087. |
| [12] | Li Xikun,Qiu Guanming,Qiu Tai,Zhao Haitao,Bai Hua,Sun Xudong.Synthesis of Al2O3/TiCN-0.2%Y2O3 Composite by Hot Pressing[J].稀土学报（英文版）,2007(03):291-295. |
| [13] | YANG H T;SHANG F L;GAO L .Microstructure and mechanical properties of gas pressure sintered Al2 O 3/TiCN composite[J].Ceramics International,2007,33:1521-1524. |
| [14] | 谢志鹏.结构陶瓷[M].北京:清华大学出版社,2011:9-24. |
| [15] | GUO W M;ZHANG G J;YANG Z G .Pressureless sintering of zirconium diboride ceramics with boron additive[J].Journal of the American Ceramic Society,2012,95(8):2470-2473. |
| [16] | 郭新 .Al2 O 3 对全稳定 ZrO 2 显微组织的影响[J].无机材料学报,1994,9(2):227-231. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%