流量阀的执行机构常应用铍青铜／钢复合元件，本文采用0.05 mm纯Ni作为中间层对QBe2.5铍青铜薄片与20#钢异种金属激光点焊搭接接头力学性能进行优化.通过光学显微镜、拉剪试验、显微硬度计和能谱测试仪对比分析添加Ni与不添加Ni层时焊接接头的成形、力学性能以及元素分布.研究表明：与未加镍层接头相比，加镍中间层的焊缝熔深较小，且基本不出现下塌现象，加镍中间层比未加中间层的接头抗拉剪力提高了61.5％；加入镍中间层后的焊缝中Fe元素含量增加，而Cu元素含量降低，接头韧性提高；加镍中间层的接头焊缝硬度值沿焊点深度方向逐渐增大，而未加镍层的基本不变，且加镍层比未加镍层的接头界面显微硬度值低.镍中间层材料可以显著改善铍青铜／钢异种金属接头焊缝熔合比，提高接头的抗拉剪强度、塑性和韧性。
Flow valve precision often uses beryllium bronze/steel composite components. In this paper, to optimize the mechanical properties of the lap joints between QBe2.5 and 20# steel, 0.05 mm-thick pure Ni is adopted as an interlayer for laser micro spot welding. The weld formation, mechanical properties and element distribution of the joints with and without Ni interlayer are contrastively analyzed through optical microscopy ( OM) , tensile shear test, microhardness tester and energy spectrum analysis( EDS) . The results showed that the tensile shear of the joint with Ni interlayer increased by 61. 5%, weld penetration decreased and did not appear to collapse basically compared with the joint without Ni interlayer. Fe content inceresed, and Cu content decreased and enhanced the joint with Ni interlayer toughness. The microhardness value increased gradually along the depth direction of the weld after joining the Ni interlayer. However, the microhardness of joint without Ni interlayer was unchanged. And the average microhardness value at the joint interface was low obviously compared with the joint with Ni interlayer. Ni interlayer materials can significantly improve the weld fusion ratio and improve the shear strength, ductility and toughness of the joints.
参考文献
| [1] | 王涛;周惦武;彭艳;张屹;陈根余.钢/铝异种金属预置Si粉的光纤激光焊接[J].中国激光,2012(3):100-107. |
| [2] | 王希靖;张亚州;李经纬;孙学敏.铝／镀锌钢搅拌摩擦铆焊接头组织与力学性能[J].材料科学与工艺,2015(2):103-108. |
| [3] | 付强;张成聪;陈玉华;黄永德.铍青铜薄片微电阻点焊工艺及接头组织性能研究[J].热加工工艺,2015(15):45-48. |
| [4] | SHUHAI CHEN;JIHUA HUANG;JUN XIA.Microstructural Characteristics of a Stainless Steel/Copper Dissimilar Joint Made by Laser Welding[J].Metallurgical and Materials Transactions, A. Physical Metallurgy and Materials Science,20138(8):3690-3696. |
| [5] | Hongwei Shen;Mool C. Gupta.Nd:yttritium-aluminum-garnet laser welding of copper to stainless steel[J].Journal of laser applications,20041(1):2-8. |
| [6] | T.A. Mai;A.C. Spowage.Characterisation of dissimilar joints in laser welding of steel-kovar, copper-steel and copper-aluminium[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,20041/2(1/2):224-233. |
| [7] | 陶汪;李俐群;王亚松;王扬.高体积分数SiCp/2024Al基复合材料添加Ti-6Al-4V中间层激光焊接特性[J].中国激光,2012(1):104-108. |
| [8] | 李洪梅;孙大千;董鹏;王文权;殷世强.TiNi形状记忆合金/不锈钢异种材料激光焊研究[J].材料工程,2011(10):47-51,57. |
| [9] | 陈玉华;谢吉林;倪泉;黄永德.铜/镀镍钢微电阻点焊接头形成机理[J].焊接学报,2015(9):35-38. |
| [10] | 李鹏 .热处理对铜镍钴合金组织性能影响的研究[D].兰州理工大学,2014. |
| [11] | 李俐群;郭伟;檀财旺.AZ31B镁合金/不锈钢异种合金双光束激光熔钎焊接特性[J].中国激光,2012(4):60-66. |
| [12] | 翟伟国 .钛-钢和铜-钢爆炸复合板的性能及界面微观组织结构[D].南京航空航天大学,2013. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%