碳纳米管因具有优异的电学、力学和热力学性能而被应用于各个领域。利用挤压工艺球磨Cu?CNT粉末制造复合材料，根据CNT的含量评估Cu?CNT复合材料的力学性能。采用行星式球磨机在500 r/min下混合分散CNT (1%,5%和10%)、铜(d=100 nm)、氧化锆球(90 g)和乙醇(20 mL)5min。用铜制造直径50 mm、长100 mm的坯锭，在单轴压力下将复合材料粉末填入坯锭。在挤压过程中，坯锭在880°C下加热1h后，坯锭负载200t，得到圆棒状样品。采用粒度分布仪测量复合材料的粒度，同时采用 SEM 观察挤压样品的表面组织。使用压痕仪测量的力学性能随着CNT含量的增加而提高。Cu?CNTs复合材料的屈服强度、抗拉强度和硬度明显提高。
Carbon nanotube (CNT)was applied in various fields for itssuperior electrical, mechanical and thermal characteristics. After composites were fabricated by extrusion processusing ball-milledCu?CNT powders, mechanicalpropertiesofCu?CNT composites according to CNT fraction were reviewed. CNT (1%, 5% and 10%),Cu (d=100 nm), zirconia balls (90 g) and ethanol (20mL) were mixed and dispersed for5h at a speed of 500 r/minusing a planetary ball mill. A billet (d=50 mm, length=100 mm) was made with Cu, and the composite powderswerefilled up into billet using the uni-axial press. In the extrusion process, after the billet was heated at 880°Cfor1h, specimens were produced in the shape of a round bar using the billet by applying a load of 200 t. The composite powdersweremeasured for particle size byparticlesize distributionequipment. Then the specimen surface fabricated by extrusion was observed by SEM. Mechanicalpropertiesmeasured by the indentation equipment increased with increasing CNT content. The yield strength, tensile strength and hardness of theCu–CNTs composites canbeobviously improved.
参考文献
| [1] | Seong-Hee Kwon;Dong-Yong Park;Dae-Yeol Lee.A Study on the Microstructure and Physical Properties of Cold Sprayed Cu/CNT Composite Coating[J].Journal of Korean Institute of Metal and Materials,20083(3):182-188. |
| [2] | A.M.K.Esawi;K.Morsi;A.Sayed;M.Taher;S.Lanka.Effect of carbon nanotube (CNT) content on the mechanical properties of CNT-reinforced aluminium composites[J].Composites science and technology,201016(16):2237-2241. |
| [3] | P. SELVAKUMAR;NARESH BHATNAGAR.Studies on Polypropylene/Carbon Fiber Composite Foams by Nozzle-Based Microcellular Injection Molding System[J].Materials and Manufacturing Processes,20094/6(4/6):533-540. |
| [4] | Dong Soo Kim;Khalid Rahman;Arshad Khan.Direct Fabrication of Copper Nanoparticle Patterns through Electrohydrodynamic Printing in Cone-Jet Mode[J].Materials and Manufacturing Processes,201210/12(10/12):1295-1299. |
| [5] | Alberto Lara-Guevara;Ignacio Rojas-Rodriguez;Ruben. Velazquez- Hernandez.Synthesis of Copper-Alumina Composites by Mechanical Milling: An Analysis[J].Materials and Manufacturing Processes,20131/3(1/3):157-162. |
| [6] | Congxu Zhu;Chan Wang;Jing Lang.Si-Coated Diamond Particles Reinforced Copper Composites Fabricated by Spark Plasma Sintering Process[J].Materials and Manufacturing Processes,20131/3(1/3):143-147. |
| [7] | Daren Li;Zuyan Liu;Yang Yu.Research on the densification of W-40 wt. percent Cu by liquid sintering and hot-hydrostatic extrusion[J].International Journal of Refractory Metals & Hard Materials,20084(4):286-289. |
| [8] | K. Morsi;A.M.K. Esawi;S. Lanka.Spark plasma extrusion (SPE) of ball-milled aluminum and carbon nanotube reinforced aluminum composite powders[J].Composites, Part A. Applied science and manufacturing,20102(2):322-326. |
| [9] | K.Y. Rhee;W.Y. Han;H.J. Park.Fabrication of aluminum/copper clad composite using hot hydrostatic extrusion process and its material characteristics[J].Materials Science & Engineering, A. Structural Materials: Properties, Misrostructure and Processing,20041/2(1/2):70-76. |
| [10] | Sung Wan Kim;Won Sub Chung;Kee-Sun Sohn.Fabrication and Fracture Properties of Alumina Matrix Composites Reinforced with Carbon Nanotubes[J].Journal of Korean Institute of Metal and Materials,20091(1):50-58. |
| [11] | Hansang Kwon;Mehdi Estili;Kenta Takagi.Combination of hot extrusion and spark plasma sintering for producing carbon nanotube reinforced aluminum matrix composites[J].Carbon: An International Journal Sponsored by the American Carbon Society,20093(3):570-577. |
- 下载量()
- 访问量()
- 您的评分：
-
10%
-
20%
-
30%
-
40%
-
50%